A multi-stage regulation strategy of space manipulators with a free-swinging joint failure

To ensure tasks can be completed after a free-swinging joint failure occurs, a multi-stage regulation strategy of space manipulators is proposed. Considering all terms of the dynamics equation, an evaluation model of the regulation ability (EMRA) of active joints over the fault joint is established based on the fuzzy entropy. And then a multi-stage regulation strategy based on the EMRA is designed to regulate the fault joint. The strategy divides the regulation process into several stages, and select a certain active joint to regulative the fault joint in every stage. With this multi-stage regulation strategy, the fault joint can be regulated to the desired angle without huge torque on regulative joints. The simulation is carried out with a 7-DOF space manipulator, verifying the correctness and effectiveness of the multi-stage regulation strategy. The strategy has three advantages: Coriolis and centrifugal terms are both considered for the first time in selecting the regulative joint, making the selection result more in line with the actual regulation process; The influence of the model uncertainty is eliminated in establishing the EMRA, making the evaluation of regulative ability more precise; The fault joint is successfully regulated to the desired angle without huge torque on regulative joints.     

天基轻气炮发射清除低轨碎片方案及关键技术分析

文章分析了现有的空间碎片清除方式,并以800~1200 km低地球轨道高度上1~10 cm量级的空间碎片为清除目标,提出了天基轻气炮清除碎片的新方法。首先分析了轻气炮有效载荷在典型参数下的弹丸加速能力;之后根据将碎片降轨使其坠入大气层烧毁的设想,提出天基轻气炮共面清除碎片的方式,并选择轨道高度800 km的圆轨道作为碎片运行轨道进行可行性分析。计算表明,对半径10 cm、厚度1 cm的铝合金圆板碎片(质量211.95 g),使用初速1 km/s、重10 g的黏性弹丸可按任务方案达到清除效果。此外,计算出该参数弹丸对轨道高度800~1200 km的圆轨道上可清除的最大碎片质量为500~825 g,证明轻气炮弹丸对1~10 cm的碎片具有较强的清除能力。最后,分析了以轻气炮为有效载荷的航天器在完成清除碎片任务时的关键技术。     

飞机液压系统柱塞泵热分析

随着飞机液压系统向高压化、大功率化方向发展，液压系统的发热及温升问题受到了广泛关注。柱塞泵作为液压系统中重要的能量转换装置，对液压系统的功率损失和温度有重大的影响，良好的柱塞泵的热分析对液压系统的热设计和温度控制有重要的意义。然而传统的柱塞泵热分析方法，如平均油温法、软件仿真法和热节点网络法，因不够准确、高效和简洁而不能满足现代飞机液压系统热分析和热设计的相关需求。本文针对飞机液压系统柱塞泵发热的相关问题，采用基于集总参数的热网络分析方法，建立了柱塞泵热网络模型，通过对柱塞泵不同工况下的仿真，验证了模型的有效性和准确性，为柱塞泵及液压系统的热分析提供了参考。     

Comparison of vertical E × B drift velocities and ground-based magnetometer observations of DELTA H in the low latitude under geomagnetically disturbed conditions

In the present work, we analyzed the daytime vertical E × B drift velocities obtained from Jicamarca Unattended Long-term Ionosphere Atmosphere (JULIA) radar and ΔH component of geomagnetic field measured as the difference between the magnitudes of the horizontal (H) components between two magnetometers deployed at two different locations Jicamarca, and Piura in Peru for 22 geomagnetically disturbed events in which either SC has occurred or Dst_max < ?50 nT during the period 2006–2011. The ΔH component of geomagnetic field is measured as the differences in the magnitudes of horizontal H component between magnetometer placed directly on the magnetic equator and one displaced 6–9° away. It will provide a direct measure of the daytime electrojet current, due to the eastward electric field. This will in turn gives the magnitude of vertical E × B drift velocity in the F region. A positive correlation exists between peak values of daytime vertical E × B drift velocity and peak value of ΔH for the three consecutive days of the events. It was observed that 45% of the events have daytime vertical E × B drift velocity peak in the magnitude range 10–20 m/s and 20–30 m/s and 20% have peak ΔH in the magnitude range 50–60 nT and 80–90 nT. It was observed that the time of occurrence of the peak value of both the vertical E × B drift velocity and the ΔH have a maximum (40%) probability in the same time range 11:00–13:00 LT. We also investigated the correlation between E × B drift velocity and D_st index and the correlation between delta H and D_st index. A strong positive correlation is found between E × B drift and D_st index as well as between delta H and D_st Index. Three different techniques of data analysis – linear, polynomial (order 2), and polynomial (order 3) regression analysis were considered. The regression parameters in all the three cases were calculated using the Least Square Method (LSM), using the daytime vertical E × B drift velocity and ΔH. A formula was developed which indicates the relationship between daytime vertical E × B drift velocity and ΔH, for the disturbed periods. The E × B drift velocity was then evaluated using the formulae thus found for the three regression analysis and validated for the ‘disturbed periods’ of 3 selected events. The E × B drift velocities estimated by the three regression analysis have a fairly good agreement with JULIA radar observed values under different seasons and solar activity conditions. Root Mean Square (RMS) errors calculated for each case suggest that polynomial (order 3) regression analysis provides a better agreement with the observations from among the three.     

Geometric error analysis of an over-constrained parallel tracking mechanism using the screw theory

This paper deals with geometric error modeling and sensitivity analysis of an overconstrained parallel tracking mechanism. The main contribution is the consideration of overconstrained features that are usually ignored in previous research. The reciprocal property between a motion and a force is applied to tackle this problem in the framework of the screw theory. First of all, a nominal kinematic model of the parallel tracking mechanism is formulated. On this basis, the actual twist of the moving platform is computed through the superposition of the joint twist and geometric errors. The actuation and constrained wrenches of each limb are applied to exclude the joint displacement. After eliminating repeated errors brought by the multiplication of wrenches, a geometric error model of the parallel tracking mechanism is built. Furthermore,two sensitivity indices are defined to select essential geometric errors for future kinematic calibration. Finally, the geometric error model with minimum geometric errors is verified by simulation with SolidWorks software. Two typical poses of the parallel tracking mechanism are selected, and the differences between simulation and calculation results are very small. The results confirm the correctness and accuracy of the geometric error modeling method for over-constrained parallel mechanisms.     

飞秒激光系统图像调焦装置以及方法

飞秒激光直写技术在复杂三维微结构加工领域具有显著优势，而调焦是否精准直接影响了所加工结构的完整度.提出了在光路中临时置入调焦光源和物的图像调焦技术，通过调节物的位置使其成像面与激光聚焦面一致，从而通过清晰可分辨的成像状态间接反映激光聚焦状态.利用Zemax软件模拟分析了原飞秒激光光路与加入调焦光源和物的调焦光路，二者可实现相同加工物镜后工作距离与良好成像质量，证明了该方法的可行性.通过分析得到该过程的成像误差主要由成像镜头焦深(3.9 μm)引起，我们获得的理想调焦精度可达到1/2焦深以内.设计了单层高度为5 μm的二层圆柱结构，通过多次实验验证了所加工元件高度误差在1.5 μm范围以内，与理论分析一致，满足飞秒激光系统的调焦要求.     

基于自适应Kriging代理模型的交叉熵重要抽样法

对于复杂失效域和小失效概率耦合的可靠性分析问题，本文提出了一种交叉熵重要抽样（CE-IS）方法结合自适应Kriging （AK）代理模型的求解方法（CE-IS-AK）。所提方法基于交叉熵原理，用混合高斯模型逐步逼近最优重要抽样密度函数，并采用AK模型协助逼近过程中混合高斯模型的参数的更新，从而提高了CE-IS方法的计算效率。另外，本文还改进了CE-IS方法的收敛准则，避免了方法的冗余迭代，扩大了方法的适用范围。由于在CE-IS方法中引入了AK模型，因此，本文方法所构建的重要抽样函数在保证精度的基础上提高了效率。相较于AK-MCS方法，本文方法中引入了重要抽样的思想，因此在Kriging训练点数目基本相同的情况下，大幅缩减小失效概率计算时样本池规模，并且由于利用了混合高斯模型，因而对多失效域具有较好的适用性。算例分析也证明了本文所提方法的优越性。     

期望状态序列导向的深空探测器规划修复方法

Aiming at the challenges caused by the persistence, concurrency and energy consumption of probe actions, a plan repair method of deep space probe based on the expected state sequence is proposed. In this method, the expected state sequence is formed of the expected effect of the unfinished action and the expected precondition of the unexecuted action in the pre designed plan, according to the execution status of the action. The expected state sequence is an ordered set of states with mixed logic and energy, providing subgoals for plan repair and also transforming the plan repair problem into the state transition path searching problem. During the search, the plan repair strategy with energy supply priority is proposed, which separates the logic repair from energy repair to reduce the difficulty of solving the problem. And this method enables the probe to recover from plan failure autonomously. Finally, the effectiveness and rationality of the proposed method are verified through simulation by taking the Mars Orbiter as an example.     

直升机新型旋翼翼型气动特性与布局分析

利用结构网格计算流体力学(Computational fluid dynamics ,CFD)的翼型气动特性分析方法开展旋翼翼型气动特性计算。通过RAE282，NACA0012，OA212，OA207等翼型压力分布、升力和阻力等特性计算结果与试验结果的对比分析，验证了计算方法的准确性，并进一步完成了HF系列旋翼翼型的气动特性计算。基于翼型的气动特性，采用时间步进自由尾迹的旋翼气动性能分析方法开展旋翼桨叶翼型的气动布局优化设计，对悬停和前飞条件下的旋翼开展计算分析，得到两种条件下的旋翼气动特性。而后通过本文建立的优化方法开展旋翼翼型布局优化设计。     

某型装备能源电池异常爆破故障分析

对一起因电池设计缺陷引发装备战训失利的故障进行分析,重点对电池工作机理和设计缺陷展开解析,明确故障定位,并对国内外装备弹上不同体系电池的优缺点进行比较,旨在为产品维护保障、国产化科研等工作提供参考。